Full-body Postural Alignment Analysis Through Barycentremetry.

STUDY DESIGN: Multicentric retrospective. OBJECTIVE: The study of center of mass (COM) locations (i.e. barycentremetry) can help us understand postural alignment. This study goal was to determine relationships between COM locations and global postural alignment X-ray parameters in healthy subjects. The second objective was to determine the impact on spinopelvic alignment of increased distance between anterior body envelope and spine at lumbar apex level. SUMMARY OF BACKGROUND DATA: Unexplored relationship between COM location and spinopelvic parameters. METHODS: This study included healthy volunteers with full-body biplanar radiograph including body envelope reconstruction, allowing the estimation of COM location. The following parameters were analyzed: lumbar lordosis (LL), thoracic kyphosis (TK), cervical lordosis (CL), pelvic tilt (PT), Sacro-femoral angle (SFA), Knee flexion angle (KFA), sagittal odontoid-hip axis angle (ODHA). The following COM in the sagittal plane were located: whole body, at thoracolumbar inflexion point, and body segment above TK apex. The body envelope reconstruction also provided the distance between anterior skin and the LL apex vertebral body center ("SV-L distance"). RESULTS: This study included 124 volunteers, with a mean age of 44±19.3. Multivariate analysis confirmed posterior translation of COM above TK apex with increasing LL (P=0.002) through its proximal component, and posterior shift of COM at inflexion point with increasing TK (P=0.008). Increased SV-L distance was associated with greater ODHA (r=0.4) and more anterior body COM (r=0.8), caused by increased TK (r=0.2) and decreased proximal and distal LL (both r=0.3), resulting in an augmentation in SFA (r=0.3) (all P<0.01). CONCLUSIONS: Barycentremetry showed that greater LL was associated with posterior shift of COM above thoracic apex while greater TK was correlated with more posterior COM at inflexion point. Whole-body COM was strongly correlated with ODHA. This study also exhibited significant alignment disruption associated with increased abdominal volume, with compensatory hip extension. LEVEL OF EVIDENCE: II.

Assessment of malalignment at early stage in adolescent idiopathic scoliosis: a longitudinal cohort study.

INTRODUCTION: Our objective was to assess abnormalities of the odontoid-hip axis (OD-HA) angle in a mild scoliotic population to determine whether screening for malalignment would help predict the distinction between progressive and stable adolescent idiopathic scoliosis (AIS) at early stage. MATERIALS AND METHODS: All patients (non-scoliotic and AIS) underwent a biplanar X-ray between 2013 and 2020. In AIS, inclusion criteria were Cobb angle between 10° and 25°; Risser sign lower than 3; age higher than 10 years; and no previous treatment. A 3D spine reconstruction was performed, and the OD-HA was computed automatically. A reference corridor for OD-HA values in non-scoliotic subjects was calculated as the range [5th-95th percentiles]. A severity index, helping to distinguish stable and progressive AIS, was calculated and weighted according to the OD-HA value. RESULTS: Eighty-three non-scoliotic and 205 AIS were included. The mean coronal and sagittal OD-HA angles in the non-scoliotic group were 0.2° and -2.5°, whereas in AIS values were 0.3° and -0.8°, respectively. For coronal and sagittal OD-HA, 27.5% and 26.8% of AIS were outside the reference corridor compared with 10.8% in non-scoliotic (OR = 3.1 and 3). Adding to the severity index a weighting factor based on coronal OD-HA, for thoracic scoliosis, improved the positive predictive value by 9% and the specificity by 13%. CONCLUSION: Analysis of OD-HA suggests that AIS patients are almost three times more likely to have malalignment compared with a non-scoliotic population. Furthermore, analysis of coronal OD-HA is promising to help the clinician distinguish between stable and progressive thoracic scoliosis.

Spinal axial torque assessment after surgical correction in adolescent idiopathic scoliosis: a new approach to 3D barycentremetry and mass distribution based on biplanar radiographs.

PURPOSE: Barycentremetry in adolescent idiopathic scoliosis (AIS) allows the distribution of masses and their loading of the spine to be studied. In particular, the axial torque on the spine has been studied in AIS, but not after surgical correction. Spinal axial torque was studied in AIS before and after surgery. METHODS: All AIS (Lenke 1 and 3) who underwent posterior spinal fusion surgery at our center in 2019 were included retrospectively. AIS underwent frontal and sagittal biplanar radiographs in the free-standing position before surgery, 4 months after surgery, and at the last follow-up. Their spine and external envelope were reconstructed with validated methods. Spinal axial torque at the apex and the upper and lower end vertebra was calculated. Finally, the preoperative and postoperative values were compared to a previously published reference corridor for asymptomatic subjects. RESULTS: Twenty-nine patients were included (54 ± 11° Cobb angle, 15 ± 2 years old at surgery). The surgical procedure decreased the Cobb angle by 36° ± 11° and decreased the spinal axial torque at the upper end vertebra by 2.5 N/m (95% CI = [1.9; 3]; p < 0.001), at the apex by 0.6 N/m (95% CI = [0.4; 1]; p = 0.004), at the lower end vertebra by 2 N/m (95% CI = [1.5; 2.8]; p < 0.001). Compared to 95th percentile of torque, which was previously evaluated in asymptomatic subjects, more than 90% of patients had higher values at the upper and lower end vertebrae before surgery. Postoperatively, 62% of patients still had higher torque at the upper end vertebra than asymptomatic subjects, while only 38% patients showed abnormal values at the lower junction. CONCLUSION: Results of this study confirm that AIS patients show abnormally high spinal axial torque, especially at the end vertebrae, and that this parameter is normalized postoperatively for only a small number of patients.

A novel antibacterial compound decreases MRSA biofilm formation without the use of antibiotics in a murine model.

Despite significant advancements in material science, surgical site infection (SSI) rates remain high and prevention is key. This study aimed to demonstrate the in vivo safety and antibacterial efficacy of titanium implants treated with a novel broad-spectrum biocidal compound (DBG21) against methicillin-resistant Staphylococcus aureus (MRSA). Titanium (Ti) discs were covalently bound with DBG21. Untreated Ti discs were used as controls. All discs were implanted either untreated for 44 control mice or DBG21-treated for 44 treated mice. After implantation, 1 × 107 colony forming units (CFU) of MRSA were injected into the operating site. Mice were killed at 7 and 14 days to determine the number of adherent bacteria (biofilm) on implants and in the peri-implant surrounding tissues. Systemic and local toxicity were assessed. At both 7 and 14 days, DBG21-treated implants yielded a significant decrease in MRSA biofilm (3.6 median log10 CFU [99.97%] reduction [p < 0.001] and 1.9 median log10 CFU [98.7%] reduction [p = 0.037], respectively) and peri-implant surrounding tissues (2.7 median log10 CFU/g [99.8%] reduction [p < 0.001] and 5.6 median log10 CFU/g [99.9997%] reduction [p < 0.001], respectively). There were no significant differences between control and treated mice in terms of systemic and local toxicity. DBG-21 demonstrated a significant decrease in the number of biofilm bacteria without associated toxicity in a small animal implant model of SSI. Preventing biofilm formation has been recognized as a key element of preventing implant-related infections.

The relationship between spino-pelvic-hip mobility and quality of life before and after total hip arthroplasty.

INTRODUCTION: Total hip arthroplasty (THA) can significantly improve quality of life (QOL) in patients with hip osteoarthritis. A relationship exists between activity levels and postoperative QOL, but its determinants are not well known. The aim of this work was to investigate the relationship between hip, pelvis and lumbar spine mobility and alignment before and after THA with QOL. MATERIAL AND METHODS: Consecutive patients with hip arthrosis and an indication for THA were included prospectively between July 2019 and December 2020, and they underwent lateral radiographs in free-standing, extension, relaxed- and flexed-seated position. Spinopelvic and hip parameters were measured, as well as their changes between positions to assess hip, pelvis and lumbar spine mobility. Patients were also administered QOL questionnaires. Data were collected preoperatively and 6 and 12 months postoperatively. RESULTS: Seventy patients were included; QOL significantly increased 6 months after THA (from 18 [10; 27] to 61 [48; 72], p < 0.001). QOL further increased by 10 points or more after 6 months in 18% of patients, while it decreased in 16%. The latter showed higher pelvic range of motion (between flexion and extension) than the former. CONCLUSIONS: This study confirmed that QOL is significantly improved by THA, and that spinopelvic alignment and function can play a role. Future work should elucidate how to better predict postoperative QOL from preoperative patient characteristics to improve patient treatment and establish early postoperative physical therapy for patients who could benefit from postoperative improvement of activity-related QOL.

Evidence of spinal stiffening following fusionless bipolar fixation for neuromuscular scoliosis: a shear wave elastography assessment of lumbar annulus fibrosus.

OBJECTIVES: There are no established criteria for stiffness after fusionless surgery for neuromuscular scoliosis (NMS). As a result, there is no consensus regarding the surgical strategy to propose at long-term follow-up. This study reports the first use of shear wave elastography for assessing the mechanical response of lumbar intervertebral discs (IVDs) after fusionless bipolar fixation (FBF) for NMS and compares them with healthy controls. The aim was to acquire evidence from the stiffness of the spine following FBF. PATIENTS AND METHODS: Nineteen NMS operated on with FBF (18 ± 2y at last follow-up, 6 ± 1 y after surgery) were included prospectively. Preoperative Cobb was 89 ± 20° and 35 ± 1° at latest follow-up. All patients had reached skeletal maturity. Eighteen healthy patients (20 ± 4 y) were also included. Shear wave speed (SWS) was measured in the annulus fibrosus of L3L4, L4L5 and L5S1 IVDs and compared between the two groups. A measurement reliability was performed. RESULTS: In healthy subjects, average SWS (all disc levels pooled) was 7.5 ± 2.6 m/s. In NMS patients, SWS was significantly higher at 9.9 ± 1.4 m/s (p < 0.05). Differences were significant between L3L4 (9.3 ± 1.8 m/s vs. 7.0 ± 2.5 m/s, p = 0.004) and L4L5 (10.3 ± 2.3 m/s vs. 7.1 ± 1.1 m/s, p = 0.0006). No difference was observed for L5S1 (p = 0.2). No correlation was found with age at surgery, Cobb angle correction and age at the SWE measurement. CONCLUSIONS: This study shows a significant increase in disc stiffness at the end of growth for NMS patients treated by FBF. These findings are a useful adjunct to CT-scan in assessing stiffness of the spine allowing the avoidance of surgical final fusion at skeletal maturity.

In-vivo characterization of the lumbar annulus fibrosus in adults with ultrasonography and shear wave elastography.

In vivo characterization of intervertebral disc (IVD) mechanical properties and microstructure could give an insight into the onset and progression of disc pathologies. Ultrasound shearwave elastography provided promising results in children, but feasibility in adult lumbar discs, which are deep in the abdomen, was never proved. The aim of this work was to determine the feasibility and reliability of ultrasound assessment of lumbar IVD in adults. Thirty asymptomatic adults were included (22 to 67 years old). Subjects were lying supine, and the annulus fibrosus of the L3-L4 IVD was imaged by conventional ultrasonography and shearwave elastography. Shear wave speed (SWS) and lamellar thickness were measured. Reliability was determined through repeated measurements acquired by three operators. Average SWS in AF at the L3L4 level was 4.0 ± 0.9 m/s, with an inter-operator uncertainty of 8.7%, while lamellar thickness was 255 ± 27 µm with an uncertainty of 9.6%. Measurement was not feasible in one out of four subjects with BMI > 24 kg/m² (overweight). Ultrasound assessment of annulus fibrosus revealed feasible, within certain limitations, and reproducible. This method gives an insight into disc microstructure and mechanical properties, and it could be applied for the early detection or follow-up of disc pathologies.

The effect of breathing on the in vivo mechanical characterization of linea alba by ultrasound shearwave elastography.

The most common surgical repair of abdominal wall hernia consists in implanting a mesh to reinforce hernia defects during the healing phase. Ultrasound shearwave elastography (SWE) is a promising non-invasive method to estimate soft tissue mechanical properties at bedside through shear wave speed (SWS) measurement. Combined with conventional ultrasonography, it could help the clinician plan surgery. In this work, a novel protocol is proposed to reliably assess the stiffness of the linea alba, and to evaluate the effect of breathing and of inflating the abdomen on SWS. Fifteen healthy adults were included. SWS was measured in the linea alba, in the longitudinal and transverse direction, during several breathing cycle and during active abdominal inflation. SWS during normal breathing was 2.3 [2.0; 2.5] m/s in longitudinal direction and 2.2 [1.9; 2.7] m/s in the transversal. Inflating the abdomen increased SWS both in longitudinal and transversal direction (3.5 [2.8; 5.8] m/s and 5.2 [3.0; 6.0] m/s, respectively). The novel protocol significantly improved the reproducibility relative to the literature (8% in the longitudinal direction and 14% in the transverse one). Breathing had a mild effect on SWS, and accounting for it only marginally improved the reproducibility. This study proved the feasibility of the method, and its potential clinical interest. Further studies on larger cohort should focus on improving our understanding of the relationship between abdominal wall properties and clinical outcomes, but also provide a cartography of the abdominal wall, beyond the linea alba.

Femoral neck version in the spinopelvic and lower limb 3D alignment: a full-body EOS® study in 400 healthy subjects.

BACKGROUND: The goal of this study was to better understand the variation of femoral neck version according to spinopelvic and lower limb 3D alignment using biplanar X-rays in standing position. METHODS: This multicentric study retrospectively included healthy subjects from previous studies who had free-standing position biplanar radiographs. Subjects were excluded if they presented spinal or any musculo-skeletal deformity, and reported pain in the spine, hip or knee. Age, sex, and the following 3D-reconstructed parameters were collected: spinal curvatures, pelvic parameters, sagittal vertical axis (SVA), T1 pelvic angle (TPA), spino-sacral angle (SSA), femoral torsion angle (FTA), sacro-femoral angle (SFA), knee flexion angle (KA), ankle angle (AA), pelvic shift (PS) and ankle distance. Femoral neck version angle (FVA) was calculated between horizontal plane projection of the bi-coxo-femoral axis and the line passing through the femoral neck barycenter and femoral head center. Analysis according to age subsets was performed. RESULTS: A total of 400 subjects were included (219 females); mean age was 29 ± 18 years (range: 4-83). Subjects with high pelvic tilt values presented significantly higher FVA than average and low-PT individuals, respectively, 7.8 ± 7.1°, 2 ± 9° and 2.1 ± 9.5° (p < 0.001). These subjects also presented lower lumbar lordosis values and higher acetabulum anteversion in the horizontal plane than the two other groups. SVA correlation with FVA was weaker (r = 0.1, p = 0.03) than SSA and TPA (r = - 0.3 and r = 0.3, respectively, p < 0.001). A strong correlation was found with femoral torsion (r = 0.5, p < 0.001). SFA (r = - 0.3, p < 0.001), pelvic shift (r = 0.2, p < 0.001) and ankle distance (r = 0.3, p < 0.001) were also significantly correlated. Multivariate analysis confirmed significant association of age, pelvic tilt, lumbar lordosis, pelvic shift, ankle distance and femoral torsion with FVA. CONCLUSION: Patients with lower lumbar lordosis present pelvic retroversion which induces a higher femoral neck version. This finding may help positioning implants in total hip replacement procedures. Higher pelvic shift, age, male gender and increased femoral torsion were also correlated with higher FVA. LEVEL OF EVIDENCE: II (Diagnostic: individual cross-sectional studies with consistently applied reference standard and blinding).

Sagittal plane assessment of manual concave rod bending for posterior correction in adolescents with idiopathic thoracic scoliosis (Lenke 1 and 3).

OBJECTIVES: The objectives of this study were to evaluate the repeatability and reproducibility of a method for measuring freehand rod bending and to analyze the relationship between the rod's bend and the resulting sagittal correction. MATERIALS AND METHODS: All the children who underwent correction by posterior translation using pedicle screws at all levels were included prospectively in 2018 and 2019. The rod's sagittal parameters were measured retrospectively by three independent surgeons on two separate occasions using the same protocol. After the rods were bent but before they were inserted, the surgeon traced the contours of the rods on a sheet of paper that was later scanned and analyzed semiautomatically. The spinal parameters were calculated based on biplanar radiographs taken preoperatively, postoperatively and at the final follow-up visit. Patients who had less than 10° thoracic kyphosis (T5-T12) made up the "Lenke N-" subgroup. RESULTS: Thirty patients were included (14 of whom were Lenke N-) who had a Cobb angle of 59.2±11.3° preoperatively and 13.3±8.4° postoperatively (p<0.00001). The inter- and intrarater ICC for the rod measurements were>0.9 (excellent). The mean kyphosis of the concave rod was 48.4±5.7° (38.3-60.9°). The mean change in T5-T12 kyphosis was 9.7±10.8° (-14.3-30.8°) (p<0.0001) in the entire population, while it was 17.7±7.1° (5.5-30.8°) (p<0.0001) in the Lenke N- subgroup. The change in thoracic kyphosis was positively correlated with the kyphosis of the concave rod (rho=0.52; p=0.003). CONCLUSION: This study found excellent reproducibility and repeatability of measuring freehand rod bending. The kyphosis applied to the concave rod is positively correlated to the change in the resulting kyphosis and made it possible to restore satisfactory thoracic kyphosis. LEVEL OF EVIDENCE: III.

Sagittal alignment in patients with flexion contracture of the hip before and after total hip arthroplasty.

INTRODUCTION: In hip osteoarthritis, hip flexion contracture can severely alter the patient's alignment, and, therefore, affect the patient's quality of life (QOL). Hip contracture is not well-studied, partly because of the difficulties of its diagnosis. The aim of this study was to propose a quantitative definition of hip flexion contracture, and to analyse sagittal alignment in these patients compared to non-contracture ones, before and 12 months after total hip arthroplasty (THA). MATERIALS AND METHODS: Consecutive patients with hip arthrosis and an indication for THA were included (N = 123). Sagittal full-body radiographs were acquired in free standing position and in extension. QOL questionnaires were administered before and after surgery. Spinopelvic parameters were measured, including the pelvic-femur angle (PFA). Patients with low pelvic incidence (< 45°) were included in the hip contracture group if PFA > 5°, or PFA > -5° when pelvic incidence ≥ 45°. RESULTS: 29% of patients were in the hip flexion contracture group, and they showed lower pelvic tilt than the no-contracture group (p < 0.001), larger lumbar lordosis (LL) and smaller PI-LL (p < 0.001), as well as a forward position of the head. 16% of patients still had hip contracture 12-months postop. Contracture patients showed higher QOL scores after surgery. CONCLUSIONS: The proposed method to diagnose hip contracture group allowed to define a group of patients who showed a specific pattern of sagittal spinopelvic alignment. These patients improved their alignment and quality of life postoperatively, but their hip mobility was not always restored. Diagnosing these patients is a first step toward the development of more specific surgical approaches, aiming to improve their surgical outcome.

Spine slenderness is not an early sign of progression in adolescent idiopathic scoliosis.

Adolescent idiopathic scoliosis (AIS) is a three-dimensional deformity of the spine. Spine slenderness, which represents its potential instability to buckling under compressive loads, was shown to be higher in AIS patients than non-scoliotic subjects, but it is not clear at what stage of the progression this difference appeared, nor if slenderness could be used as an early sign of progression. In this study, we hypothesized that slenderness could be an early sign of progression. One-hundred thirty-eight patients and 93 non-scoliotic subjects were included. They underwent standing biplanar radiography and 3D reconstruction of the spine, which allowed computing vertebra and disc slenderness ratio. Then, patients were followed until progression of the deformity or skeletal maturity (stable patients). Vertebral slenderness ratio in AIS patients varied between 2.9 [2.7; 3.0] (T9) and 3.4 [3.2; 3.6] (T1), while disc slenderness ranged from 0.6 [0.6; 0.7] at T6-T7 to 1.2 [1.1; 1.3] at L4-L5. Slenderness ratio increased with age, while disc slenderness tended to decrease with age and Cobb angle. Slenderness was similar between progressive and stable patients, and also between patients and non-scoliotic subjects. In conclusion, spinal slenderness does not appear to be an early sign of progression. Further studies should analyse the development of slenderness during growth, and how it could be affected by non-operative treatment.

The rib cage: a new element in the spinopelvic chain.

INTRODUCTION: This study analyzes anatomical variations of the thoracic cage (TC) according to spinopelvic alignment, age and gender using stereoradiography in erect position. METHODS: This retrospective multicentric study analyzed computed parameters collected from free-standing position bi-planar radiographs, among healthy subjects. Collected data were: age, gender, pelvic parameters (Pelvic Incidence, Pelvic Tilt (PT) and Sacral Slope), T1-T12 Kyphosis (TK), L1-S1 Lordosis (LL), curvilinear spinal length, global TC parameters (maximum thickness and width, rib cage volume, mean Spinal Penetration Index (SPI)), 1st-10th rib parameters (absolute and relative (to the corresponding vertebra) sagittal angles). RESULTS: Totally, 256 subjects were included (140 females). Mean age was 34 (range: 8-83). Significant correlations were found between TK and TC thickness (0.3, p < 0.001) and with TC Volume (0.3, p = 0.04), as well as rib absolute sagittal angle for upper and middle ribs (0.2, p = 0.02). Conversely, a -0.3 correlation has been exhibited between SPI and TK. Similar correlations were found with LL. PT significantly correlated with TC thickness (0.4, p = 0.003), SPI (-0.3, p = 0.03), and all rib relative sagittal angles. Among global TC parameters, only thickness and SPI significantly changed after 20 years (respectively, 0.39 and -0.52, p < 0.001). Ribs relative sagittal angle showed negative correlation with age in skeletally mature subjects (p < 0.001). CONCLUSION: This study demonstrates the correlation between TC anatomy and spinopelvic parameters, confirming its part of the spinopelvic chain of balance. Indeed, higher spinal curvatures were associated with lower SPI and higher TC thickness, TC volume and rib absolute sagittal angles.

An analysis on the determinants of head to pelvic balance in a Chinese adult population.

Background: Balanced global spinopelvic balance is important in the maintenance of the physiological alignment of all body segments above the pelvis with minimum energy expenditure. The key determinants affecting the 3D index-odontoid-hip axis (OD-HA) angle, and in particular its alterations, have not been clearly defined. The aim of this study is to identify the determinants of the 3D OD-HA angle in maintaining global spinopelvic balance in a large Chinese adult cohort of different gender and age groups. Methods: A total of 516 asymptomatic adults were enrolled in this study. Biplanar radiographies were performed to reconstruct the subject's inter-acetabular axis and C2 odontoid process. The 3D angle formed by the vertical and the line between odontoid and mid-interacetabular axis (OD-HA angle) was computed and projected in the subject's sagittal and coronal planes. Thoracic kyphosis (TK), lumbar lordosis (LL), T1 pelvic angle (TPA) and sagittal vertical axis (SVA) were measured. Results: The mean values of sagittal and coronal OD-HA were -0.2°±2.5° and 0.2°±1.1°, respectively. Both sagittal and coronal OD-HA had significant correlation with age (r=0.265 and r=-0.143, P<0.01, respectively), sagittal OD-HA showed increment from 20s to 80s (-1.3° to 0.8° for female, -0.3° to 1.5° for male) and a significant difference between male and female from 20 to 69 years old. Further analysis showed that sex, weight, TK, PT, SVA, TPA and ODI were determinants of OD-HA. Conclusions: 3D OD-HA angle showed physiological stability with little variability from young to elderly adults, with SD of 2.45° and 1.06° in sagittal and coronal planes, respectively. OD-HA angle confirms the hypothesis that the head tends to remain above the pelvis in a small cone of stability. This study provides an analysis of the determinants of OD-HA and the reference range of the head-pelvis balance in each decade and gender based on a large-scale asymptomatic population.

Functional analysis of the human rib cage over the vital capacity range in standing position using biplanar X-ray imaging.

Pathologies of the respiratory system can by accompanied by alterations of the biomechanical function of the rib cage, as well as of its morphology and movement. The assessment of such pathologies could benefit from rib cage kinematic analysis during breathing, but this analysis is challenging because of the difficulties in observing and quantifying bone movements in vivo. This work explored the feasibility of using biplanar x-rays to study rib cage modifications at different lung volumes and evaluated the potential of the method to characterize rib cage kinematic patterns in patients. Forty-seven asymptomatic adults and eleven obstructive sleep apnea syndrome (OSAS) patients underwent biplanar x-rays at three lung volumes: normal breathing, maximal and minimal volume. Rib cage and spinopelvic positional parameters were computed from 3D reconstruction of the skeleton. Results showed that inspiration mostly mobilized the ribs and costo-vertebral junction, while expiration was driven by the spine. OSAS patients had a different sagittal profile at rest than asymptomatic subjects, but these differences decreased at maximal and minimal volume. This suggests that patients employed different biomechanical strategies to attain a trunk configuration similar to asymptomatic subjects at minimal and maximal lung volume. This study confirmed that the proposed method could have an impact for the clinical assessment and understanding of pathologies involving breathing function, and which directly affect rib cage morphology.

Global malalignment in adolescent idiopathic scoliosis: the axial deformity is the main driver.

PURPOSE: To evaluate the global alignment of non-operated subjects with adolescent idiopathic scoliosis. METHOD: A total of 254 subjects with AIS and 64 controls underwent low dose biplanar X-rays and had their spine, pelvis, and rib cage reconstructed in 3D. Global alignment was measured in the sagittal and frontal planes by calculating the OD-HA angle (between C2 dens to hip axis with the vertical). Subjects with AIS were classified as malaligned if the OD-HA was > 95th percentile relative to controls. RESULTS: The sagittal OD-HA in AIS remained within the normal ranges. In the frontal plane, 182 AIS were normally aligned (Group 1, OD-HA = 0.9°) but 72 were malaligned (Group 2, OD-HA = 2.9°). Group 2 had a more severe spinal deformity in the frontal and horizontal planes compared to Group 1 (Cobb: 42 ± 16° vs. 30 ± 18°; apical vertebral rotation AVR: 19 ± 10° vs. 12 ± 7°, all p < 0.05). Group 2 subjects were mainly classified as Lenke 5 or 6. 19/72 malaligned subjects had a mild deformity (Cobb < 30°) but a progressive scoliosis (severity index ≥ 0.6). The frontal OD-HA angle was found to be mainly determined (adjusted-R2 = 0.22) by the apical vertebral rotation and secondarily by the Lenke type. CONCLUSIONS: This study showed that frontal malalignment is more common in distal major structural scoliosis and its main driver is the apical vertebral rotation. This highlights the importance of monitoring the axial plane deformity in order to avoid worsening of the frontal global alignment.

Contribution of shear wave elastography in evaluation of the deltoid in reverse shoulder arthroplasty: reproducibility study and preliminary results.

AIMS: The current difficulty of reverse shoulder arthroplasty (RSA) is soft tissue management, and adequate deltoid tension and at present there is no consensus and available tools (X-ray, MRI, EMG) remain difficult to apply in clinical follow-up. The objective of this study was (1) to determine reliability and feasibility of deltoid elasticity assessment using ultrasound elastographyand (2) to assess the change of deltoid stiffness after RSA by comparing shear wave speed (SWS) between healthy and RSA shoulders. MATERIAL AND METHODS: Twenty-six healthy (native shoulder, painless and complete range of motion) subjects and twelve patients with RSA were included. Two independent investigators performed 3 measurements on each segment. Measurements were bilateral. Anterior segment was also evaluated at 45° and 60° of passive abduction. Reliability and feasibility have been assessed (ISO5725-standard). RESULTS: Coefficient of measurements variation was less than 6.1% and 0.13 m/s. In the healthy group, SWS was not significantly different between anterior and middle segments; however, the SWS of the posterior segment was significantly lower than others (p<0.0001). In abduction position, compared to the rest position, SWS of the anterior segment decreased at 45° abduction (p=0.0003) and increased at 60° abduction (p<0.0001). Variability of measurement was higher in the RSA group. No significant difference was found between the SWS measurement of the operated and non-operated side. SWS measurements of the operated side of the anterior and middle segment were significantly higher compared to the healthy group. In abduction position, compared to rest position, no difference in SWS of the anterior segment was found at 45° abduction (p=0.71) and nor at 60° abduction (p=0.75). CONCLUSION: This study demonstrated feasibility and reliability of shoulder assessment with shear wave elastography. Reference values for asymptomatic patients can already be used in future studies on shoulder pathology and surgery.

Assessment of the axial plane deformity in subjects with adolescent idiopathic scoliosis and its relationship to the frontal and sagittal planes.

PURPOSE: Investigate the axial plane deformity in the scoliotic segment and its relationship to the deformity in the frontal and sagittal planes. METHODS: Two hundred subjects with AIS (Cobb ≥ 20°) underwent low dose biplanar X-rays with 3D reconstruction of the spine and pelvis. All structural curves were considered and were distributed as follows: 142 thoracic (T), 70 thoracolumbar (TL), and 47 lumbar curves (L). Common 3D spino-pelvic and scoliosis parameters were collected such as: frontal Cobb; torsion index (TI); hypokyphosis/lordosis index (HI). Parameters were compared between each type of curvature and correlations were investigated between the 3 planes. RESULTS: Frontal Cobb was higher in all T (45 ± 19°) and TL (41 ± 15°) curves compared to L curves (35 ± 14°, p = 0.004). TI was higher in T curves when compared to TL and L curves (TI: 15 ± 8°, 9 ± 6°, 7 ± 5°, p < 0.001). HI was similar between curve types. T curves showed significant correlations between the 3 planes: Cobb vs. TI (r = 0.76), Cobb vs. HI (r = - 0.54) and HI vs. TI (r = - 0.42). The axial plane deformity was related to the frontal deformity and the type of curvature (adjusted-R2 = 0.6). CONCLUSION: Beside showing the most severe deformity frontally and axially compared to TL and L curves, the T curves showed strong correlations between the 3 planes of the deformity. Moreover, this study showed that the axial plane deformity cannot be fully determined by the frontal and sagittal deformities, which highlights the importance of 3D assessment in the setting of AIS.

Estimating pulmonary function after surgery for adolescent idiopathic scoliosis using biplanar radiographs of the chest with 3D reconstruction.

AIMS: This study addressed two questions: first, does surgical correction of an idiopathic scoliosis increase the volume of the rib cage, and second, is it possible to evaluate the change in lung function after corrective surgery for adolescent idiopathic scoliosis (AIS) using biplanar radiographs of the ribcage with 3D reconstruction? METHODS: A total of 45 patients with a thoracic AIS which needed surgical correction and fusion were included in a prospective study. All patients underwent pulmonary function testing (PFT) and low-dose biplanar radiographs both preoperatively and one year after surgery. The following measurements were recorded: forced vital capacity (FVC), slow vital capacity (SVC), and total lung capacity (TLC). Rib cage volume (RCV), maximum rib hump, main thoracic curve Cobb angle (MCCA), medial-lateral and anteroposterior diameter, and T4-T12 kyphosis were calculated from 3D reconstructions of the biplanar radiographs. RESULTS: All spinal and thoracic measurements improved significantly after surgery (p < 0.001). RCV increased from 4.9 l (SD 1) preoperatively to 5.3 l (SD 0.9) (p < 0.001) while TLC increased from 4.1 l (SD 0.9) preoperatively to 4.3 l (SD 0.8) (p < 0.001). RCV was correlated with all functional indexes before and after correction of the deformity. Improvement in RCV was weakly correlated with correction of the mean thoracic Cobb angle (p = 0.006). The difference in TLC was significantly correlated with changes in RCV (p = 0.041). It was possible to predict postoperative TLC from the postoperative RCV. CONCLUSION: 3D rib cage assessment from biplanar radiographs could be a minimally invasive method of estimating pulmonary function before and after spinal fusion in patients with an AIS. The 3D RCV reflects virtual chest capacity and hence pulmonary function in this group of patients. Cite this article: Bone Joint J 2022;104-B(1):112-119.